... heat transfer efficiency, a new heterogeneous PCHE with MS zigzag passage and sCO 2 airfoil fin passage was proposed. A one-dimensional simulation of the new PCHE was conducted to study the effects of the plate number and the length on its pressure drop, MS mass flowrate, capital cost, and operating...

...Chandan Mukherjee; Sudipto Mukhopadhyay In non-isothermal flows, heatlines are used to depict the energy flow from hot surface to cold surface and help in visualizing the strength of the convective heat transfer as compared to the conductive heat transfer. Traditionally, researchers have plotted...

... function, using the pseudo-elasticity theory and the inverse analysis method. This equation was utilized to calculate the internal heat generation rates of rubber compounds. With heat generation rates, the governing equation of heat conduction and the mathematical expression of boundary conditions were...

... average temperature were separately applied in the topological optimization of two typical uniform heat generation cases, and the resulted topologically optimization results were analyzed and compared. Based on the two benchmark cases, the appropriate objective function was selected to conduct structural...

... energy utilization. This paper presents a thermal management system of vapor compression with a combination of active and passive cooling. The system uses insulation materials to isolate the high-temperature environment, thermally conductive silicone grease to strengthen the heat exchange...

..., PT, and CT increases as the input heat flux is increased; this is because as the heat flux increases more heat is transferred from fuel bundle to PT, CT, and moderator through convection and conduction. It is also observed that at a heat flux value greater than or equal to 2500 W/m 2 , the boiling...

... lobed nozzle conduction forced convection heat and mass transfer radiative heat transfer thermal systems Science and Engineering Research Board 10.13039/501100001843 ECR/2017/001305 1 Corresponding author. Email: arnabapun@gmail.com Email: vikrantmechboy@gmail.com...

... Thermal conductivity, k (W/(m · °C)) 38 45 Specific heat capacity, c (J/(kg · °C)) 377 460 Thermal behaviors of the conical friction element under different contact pressure boundaries are investigated according to the analysis flow shown in Fig. 2 . Fig. 2 Analysis flowchart...

... approaches used to calculate the Nusselt number in miniature heat sinks. It is observed that three major parameters including (1) axial heat conduction within the solid substrate of heat sinks, (2) thermal contact resistance, and (3) assumed uniform wall temperature, as well as wall heat flux distributions...

... Corresponding author. Email: hlhuang@nuaa.edu.cn 24 11 2021 17 02 2022 23 02 2022 11 04 2022 PCHE flow and heat transfer characteristics numerical simulation coupled heat transfer aerospace heat transfer conduction heat and mass transfer heat exchangers heat transfer...

... by about 10%, the SRI increases by the same percentage and the TrUI increases by less than 5%. This is because for the considered range of Re the conduction resistance inside the brick becomes the bottleneck of the process in accordance with the findings of Ref. [ 40 ] and considering the relatively large...

... combined hole crescent rib anti-kidney vortex conduction forced convection gas turbine heat transfer National Natural Science Foundation of China 10.13039/501100001809 51676163 The thermal efficiency and power output of a gas turbine are highly dependent on the turbine inlet...

... Stefan number natural convection LHTES conduction energy systems heat exchangers melting and solidification The annual global energy demand can be met through solar energy radiation falling on the earth’s surface in one day [ 1 ]. Despite the fact, fossil fuels dominantly contribute...

...Pranab Kanti Roy We present a mathematical model of flat-plate solar collector whose thermal conductivity is a power law function of temperature, and nondimensional length is governed by a profile index. The rectangular, convex, and triangular shape absorber plates are obtained by changing...

... insulation panel thermal radiation harsh environment heat flow direction index active thermal management system thermal protection conduction electronic cooling experimental techniques radiative heat transfer Electronics architecture design and its manufacturing trend exhibit a tremendous...

... 2020 19 06 2021 22 06 2021 13 10 2021 boiling bubbles particles and droplets conduction energy systems experimental techniques experimental/measurement techniques forced convection heat and mass transfer heat transfer enhancement radiative heat transfer thermal systems...

.... , and Egry , I. , 2003 , “ Density Determination of Liquid Copper, Nickel, and Their Alloys ,” Int. J. Thermophys. , 24 ( 4 ), pp. 1572 – 9567 . 10.1023/A:1025021521945 h = sensible enthalpy k = thermal conductivity p = pressure t = time H = specific...

... . The length of the axial segment is long enough to ensure that the radiation occurs only between surface elements and gas of the same axial segment. In an axial segment, the axial conduction in the refractory wall and axial radiation in the enclosure are neglected. The refractory wall and the surface...

...Savannah S. Wessies; Ofodike A. Ezekoye In many industrial cooling and fire safety applications, multimode heat transfer involving radiation, convection, and conduction cools hot objects deposited on substrates. In some cases, the convective cooling is due to impinging jets on a flat surface...

...@bucci-industries.com Email: n.vincenzi@bucci-industries.com 23 09 2020 02 02 2021 04 02 2021 16 03 2021 conduction experimental techniques experimental/measurement techniques thermal systems The accuracy of a workpiece produced by a metal-cutting machine...