In this study, heat transfer and fluid flow of de-ionized water in two-dimensional parallel plates microchannel with and without micromixers have been investigated for various Reynolds numbers. The effects of heat transfer and fluid flow on height, diameter of micromixer, and also distance between the two micromixers are carried out in the study. Results showed that the diameter of the micromixer does not have much effect on heat transfer with a maximum enhancement of 9.5%. Whereas heat transfer gets enhanced by 85.57% when the height of the micromixer is increased from 100 μm to 400 μm, and also heat transfer gets improved by 11.45% when sb2 is increased from 4L to 5L. The separation and reattachment zone at the entry and exit of the micromixer cause the increase in heat transfer with the penalty of pressure drop. It is also found that increase of Reynolds number increases the intensity of the secondary flows leads to rapid increase in heat transfer and pressure drop. Finally, the optimized structure of micromixer is found out based on maximum heat transfer and minimum pressure drop.
Skip Nav Destination
Article navigation
February 2018
Research-Article
Numerical Analysis of Fluid Flow and Heat Transfer of Flow Between Parallel Plates Having Rectangular Shape Micromixer
Sudip Shyam,
Sudip Shyam
Department of Mechanical Engineering,
NIT Agartala,
Agartala 799046, India
e-mail: sudipme2012@gmail.com
NIT Agartala,
Agartala 799046, India
e-mail: sudipme2012@gmail.com
Search for other works by this author on:
Ajoy Kumar Das
Ajoy Kumar Das
Search for other works by this author on:
Sudip Shyam
Department of Mechanical Engineering,
NIT Agartala,
Agartala 799046, India
e-mail: sudipme2012@gmail.com
NIT Agartala,
Agartala 799046, India
e-mail: sudipme2012@gmail.com
Aparesh Datta
Ajoy Kumar Das
1Corresponding authors.
Contributed by the Heat Transfer Division of ASME for publication in the JOURNAL OF THERMAL SCIENCE AND ENGINEERING APPLICATIONS. Manuscript received September 9, 2016; final manuscript received January 24, 2017; published online June 27, 2017. Assoc. Editor: Qingang Xiong.
J. Thermal Sci. Eng. Appl. Feb 2018, 10(1): 011003 (8 pages)
Published Online: June 27, 2017
Article history
Received:
September 9, 2016
Revised:
January 24, 2017
Citation
Shyam, S., Datta, A., and Kumar Das, A. (June 27, 2017). "Numerical Analysis of Fluid Flow and Heat Transfer of Flow Between Parallel Plates Having Rectangular Shape Micromixer." ASME. J. Thermal Sci. Eng. Appl. February 2018; 10(1): 011003. https://doi.org/10.1115/1.4036769
Download citation file:
Get Email Alerts
Cited By
Performance Analysis of a Phase Changing Material Based Thermocycler for Nucleic Acid Amplification
J. Thermal Sci. Eng. Appl (May 2023)
Numerical Investigation on Heat Flux Variation in Fuel Bundle Over Fully Voided Concentric Channel of IPHWR Under Severe Accidental Scenario
J. Thermal Sci. Eng. Appl (May 2023)
A Novel Non-Intrusive Imaging Technique to Quantify Shrinkage of Elephant Foot Yam During Convective Drying
J. Thermal Sci. Eng. Appl (May 2023)
Multi-objective optimization of an inlet air-cooled combined cycle power plant
J. Thermal Sci. Eng. Appl
Related Articles
Experimental Study of Single Phase Heat Transfer and Pressure Loss in a Spiraling Radial Inflow Microchannel Heat Sink
J. Heat Transfer (July,2015)
Probing the Local Heat Transfer Coefficient of Water-Cooled Microchannels Using Time-Domain Thermoreflectance
J. Heat Transfer (November,2017)
Experimental Study of Water Flow and Heat Transfer in Silicon Micro-Pin-Fin Heat Sinks
J. Heat Transfer (December,2018)
Related Proceedings Papers
Related Chapters
Hydraulic Resistance
Heat Transfer & Hydraulic Resistance at Supercritical Pressures in Power Engineering Applications
Plate Exchangers
Heat Exchanger Engineering Techniques
Analytical and Numerical Methods in Fluid Flow and Heat Transfer
Applications of Mathematical Heat Transfer and Fluid Flow Models in Engineering and Medicine