Abstract
This paper proposes a reconfigurable wheeled mobile platform (RWMP) consisting of two two-wheeled mobile robots and a reconfigurable trunk. The reconfigurable trunk is a 6R multi-mode single-loop mechanism (SLM) that is obtained by inserting two revolute (R) joints with intersected axes into a planar rhombus 4R mechanism. The 6R mechanism has reconfigurable characteristics owing to changes in the wrench system. All six motion modes and their constraint equations of the 6R mechanism are obtained by solving the closed-loop equation based on the D-H transformation matrix. The analysis shows that the mechanism has six single-DOF motion modes, including a planar rhombus 4R mode, two overconstrained spatial 6R modes, and three coaxial 1R modes. The motion characteristics of the six motion modes are identified using screw theory. The six transition configurations among different modes are identified by combining the constraint equations of each mode. The locomotion modes of the RWMP are designed based on the reconfiguration analysis of the trunk mechanism. The locomotion effect of the RWMP under two confined spaces is verified by simulation analysis and prototype experiment.
Graphical Abstract Figure
References
1.
Zhang
, K. T.
, and Dai
, J. S.
, 2014
, “A Kirigami-Inspired 8R Linkage and Its Evolved Overconstrained 6R Linkages With the Rotational Symmetry of Order Two
,” ASME J. Mech. Rob.
, 6
(2
), p. 021007
. 2.
Ma
, X.
, Zhang
, K. T.
, and Dai
, J. S.
, 2018
, “Novel Spherical-Planar and Bennett-Spherical 6R Metamorphic Linkages With Reconfigurable Motion Branches
,” Mech. Mach. Theory
, 128
, pp. 628
–647
. 3.
Chai
, X.
, Kang
, X.
, Gan
, D.
, Yu
, H.
, and Dai
, J. S.
, 2021
, “Six Novel 6R Metamorphic Mechanisms Induced From Three-Series-Connected Bennett Linkages That Vary among Classical Linkages
,” Mech. Mach. Theory
, 156
, p. 104133
. 4.
Zhang
, K. T.
, and Dai
, J. S.
, 2016
, “Geometric Constraints and Motion Branch Variations for Reconfiguration of Single-Loop Linkages With Mobility One
,” Mech. Mach. Theory
, 106
, pp. 16
–29
. 5.
Wang
, R.
, Song
, Y.
, and Dai
, J. S.
, 2021
, “Reconfigurability of the Origami-Inspired Integrated 8R Kinematotropic Metamorphic Mechanism and Its Evolved 6R and 4R Mechanisms
,” Mech. Mach. Theory
, 161
, p. 104245
. 6.
Tang
, Z.
, and Dai
, J. S.
, 2018
, “Bifurcated Configurations and Their Variations of an 8-Bar Linkage Derived From an 8-Kaleidocycle
,” Mech. Mach. Theory
, 121
, pp. 745
–754
. 7.
Chai
, X.
, Zhang
, C.
, and Dai
, J. S.
, 2018
, “A Single-Loop 8R Linkage with Plane-Symmetry and Bifurcation Property
,” International Conference on Reconfigurable Mechanisms and Robots
, Delft, Netherlands
, June 20–22
, IEEE, pp. 1–8
.8.
Song
, Y.
, Ma
, X.
, and Dai
, J. S.
, 2019
, “A Novel 6R Metamorphic Mechanism With Eight Motion Branches and Multiple Furcation Points
,” Mech. Mach. Theory
, 142
, p. 103598
. 9.
Kang
, X.
, Ma
, X.
, Dai
, J. S.
, and Yu
, H.
, 2020
, “Bifurcation Variations and Motion-Ruled-Surface Evolution of a Novel Schatz Linkage Induced Metamorphic Mechanism
,” Mech. Mach. Theory
, 150
, p. 103867
. 10.
Zhang
, K. T.
, and Liu
, C.
, 2021
, “Design and Analysis of a Novel Reconfigurable Parallel Manipulator With Kirigami-Inspired Bennett Plano-Spherical Linkages and Angular Pouch Motors
,” ASME J. Mech. Rob.
, 13
(4
), p. 040911
. 11.
Kong
, X.
, and Huang
, C.
, 2009
, “Type Synthesis of Single-DOF Single-Loop Mechanisms With Two Operation Modes
,” Reconfigurable Mechanisms and Robots
, London, UK
, June 22–24
, IEEE, pp. 136–141
.12.
Kong
, X.
, and Pfurner
, M.
, 2015
, “Type Synthesis and Reconfiguration Analysis of a Class of Variable-DOF Single-Loop Mechanisms
,” Mech. Mach. Theory
, 85
, pp. 116
–128
. 13.
He
, X.
, Kong
, X.
, Hao
, G.
, and Ritchie
, J.
, 2016
, “Design and Analysis of a new 7R Single-Loop Mechanism with 4R, 6R and 7R Operation Modes
,” Reconfigurable Mechanisms and Robots
, Beijing, China
, July 20–22
, IEEE, pp. 27–37
.14.
Kong
, X.
, and Muller
, A.
, 2018
, “A Single-Loop 7R Spatial Mechanism That Has Three Models With the Same Instantaneous DOF but Different Finite DOF
,” Proceedings of ASME 2018 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference
, ASME Paper No. DETC2018-85125.15.
Kong
, X.
, 2018
, “A Variable-DOF Single-Loop 7R Spatial Mechanism With Five Motion Modes
,” Mech. Mach. Theory
, 120
, pp. 239
–249
. 16.
He
, X.
, Kong
, X.
, Chablat
, D.
, Caro
, S.
, and Hao
, G.
, 2014
, “Kinematic Analysis of a Single-Loop Reconfigurable 7R Mechanism With Multiple Operation Modes
,” Robotica
, 32
(7
), pp. 1171
–1188
. 17.
Liu
, K.
, Yu
, J
, and Kong
, X.
, 2021
, “Synthesis of Multi-Mode Single-Loop Bennett-Based Mechanisms Using Factorization of Motion Polynomials
,” Mech. Mach. Theory
, 155
, p. 104110
. 18.
Galletti
, C.
, and Fanghella
, P.
, 2001
, “Single-Loop Kinematotropic Mechanisms
,” Mech. Mach. Theory
, 36
(6
), pp. 743
–761
. 19.
Fanghella
, P.
, 2009
, “Stability of Branches of a Kinematotropic Mechanism
,” International Conference on Reconfigurable Mechanisms and Robots
, London, UK
, June 22–24
, IEEE, pp. 41–46
.20.
Zeng
, Q.
, Ehmann
, K. F.
, and Cao
, J.
, 2016
, “Design of General Kinematotropic Mechanisms
,” Rob. Comput. Integr. Manuf.
, 38
, pp. 67
–81
. 21.
Lee
, C. C.
, and Hervé
, J. M.
, 2005
, “Discontinuously Movable Seven-Link Mechanisms via Group-Algebraic Approach
,” Proc. Inst. Mech. Eng. C J. Mech. Eng. Sci.
, 219
(6
), pp. 577
–587
. 22.
Lo
, T.
, Yang
, T.
, and Lee
, J.
, 2018
, “Synthesis of Discontinuously Movable Mechanisms With Bifurcation
,” International Conference on Reconfigurable Mechanisms and Robots
, Delft, Netherlands
, June 20–22
, IEEE, pp. 1–8
.23.
Zlatanov
, Dimiter
, Bonev
, Ilian
, and Gosselin
, Clément
, 2002
, “Constraint Singularities as C-Space Singularities,” Advances in Robot Kinematics
, Springer
, Dordrecht
, pp. 183
–192
.24.
Song
, C.
, Chen
, Y.
, and Chen
, I.
, 2014
, “Kinematic Study of the Original and Revised General Line-Symmetric Bricard 6R Linkages
,” ASME J. Mech. Rob.
, 6
(3
), p. 031002
. 25.
Ma
, X.
, Zhang
, X.
, and Dai
, J. S.
, 2018
, “Motion Cycle and Configuration Torus With Their Relationship to Furcation During Reconfiguration
,” ASME J. Mech. Rob.
, 10
(5
), p. 051006
. 26.
Feng
, H.
, Chen
, Y.
, Dai
, J. S.
, and Gogu
, G.
, 2017
, “Kinematic Study of the General Plane-Symmetric Bricard Linkage and Its Bifurcation Variations
,” Mech. Mach. Theory
, 116
, pp. 89
–104
. 27.
Chai
, X.
, and Dai
, J. S.
, 2019
, “Three Novel Symmetric Waldron–Bricard Metamorphic and Reconfigurable Mechanisms and Their Isomerization
,” ASME J. Mech. Rob.
, 11
(5
), p. 051011
. 28.
Huang
, C.
, Kong
, X.
, and Ou
, T.
, 2009
, “Position Analysis of a Bennett-Based Multiple-Mode 7R Linkage
,” Proceedings of ASME 2009 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference
, ASME Paper No. DETC2009-87241.29.
Huang
, C.
, Tseng
, R.
, and Kong
, Xianwen
, 2010
, “Design and Kinematic Analysis of a Multiple-Mode 5R2P Closed-Loop Linkage,” New Trends in Mechanism Science
, Springer
, New York
, pp. 3
–10
.30.
Pfurner
, M.
, and Kong
, X.
, 2016
, “Algebraic Analysis of a New Variable-DOF 7R Mechanism,” New Trends in Mechanism and Machine Science, Theory and Industrial Applications
, P.
Wenger
and P.
Flores
, eds., Springer
, New York
, pp. 71
–79
.31.
Kong
, X.
, 2017
, “Reconfiguration Analysis of Multimode Single-Loop Spatial Mechanisms Using Dual Quaternions
,” ASME J. Mech. Rob.
, 9
(5
), p. 051002
. 32.
Liu
, K.
, Yu
, J.
, and Kong
, X.
, 2022
, “Structure Synthesis and Reconfiguration Analysis of Variable-Degree-of-Freedom Single-Loop Mechanisms With Prismatic Joints Using Dual Quaternions
,” ASME J. Mech. Rob.
, 14
(2
), p. 021009
. 33.
Pfurner
, M.
, Kong
, X.
, and Huang
, C.
, 2014
, “Complete Kinematic Analysis of Single-Loop Multiple-Mode 7-Link Mechanisms Based on Bennett and Overconstrained RPRP Mechanisms
,” Mech. Mach. Theory
, 73
, pp. 117
–129
. 34.
Zhang
, C.
, Zhang
, C.
, Dai
, J. S.
, and Qi
, P.
, 2019
, “Stability Margin of a Metamorphic Quadruped Robot With a Twisting Trunk
,” ASME J. Mech. Rob.
, 11
(6
), p. 064501
. 35.
Tang
, Z.
, Wang
, K.
, Spyrakos-Papastavridis
, E.
, and Dai
, J. S.
, 2022
, “Origaker: A Novel Multi-Mimicry Quadruped Robot Based on a Metamorphic Mechanism
,” ASME J. Mech. Rob.
, 14
(6
), p. 060907
. 36.
Wu
, J.
, Yang
, H.
, Li
, R.
, Ruan
, Q.
, Yan
, S.
, and Yao
, Y.-A.
, 2021
, “Design and Analysis of a Novel Octopod Platform With a Reconfigurable Trunk
,” Mech. Mach. Theory
, 156
, p. 104134
. 37.
Li
, Y.
, Yao
, Y.-A.
, and He
, Y.
, 2018
, “Design and Analysis of a Multi-Mode Mobile Robot Based on a Parallel Mechanism With Branch Variation
,” Mech. Mach. Theory
, 130
, pp. 276
–300
. 38.
Dai
, J. S.
, and Wang
, D.
, 2007
, “Geometric Analysis and Synthesis of the Metamorphic Robotic Hand
,” ASME J. Mech. Des.
, 129
(11
), pp. 1191
–1197
. 39.
Dai
, J. S.
, Wang
, D.
, and Cui
, L.
, 2009
, “Orientation and Workspace Analysis of the Multifingered Metamorphic Hand-Metahand
,” IEEE Trans. Rob.
, 25
(4
), pp. 942
–947
. 40.
Cui
, L.
, and Dai
, J. S.
, 2011
, “Posture, Workspace, and Manipulability of the Metamorphic Multifingered Hand With an Articulated Palm
,” ASME J. Mech. Rob.
, 3
(2
), p. 021001
. 41.
Cui
, L.
, and Dai
, J. S.
, 2012
, “Reciprocity-Based Singular Value Decomposition for Inverse Kinematic Analysis of the Metamorphic Multifingered Hand
,” ASME J. Mech. Rob.
, 4
(3
), p. 034502
. 42.
Zheng
, Y.
, Tang
, Z.
, and Dai
, J. S.
, 2018
, “A Mapping Method of Grasping Posture Applying to the Metamorphic Multi-Fingered Hand
,” International Conference on Reconfigurable Mechanisms and Robots
, Delft, Netherlands
, June 20–22
, IEEE, pp. 1–7
.43.
Lyu
, S.
, Xu
, T.
, Ding
, X.
, and Xiao
, H.
, 2022
, “A Reconfigurable Modular Fixture With Redundant Actuation
,” ASME J. Mech. Rob.
, 14
(6
), p. 060901
. 44.
Kim
, S.
, Seo
, J.
, and Kwon
, S.
, 2011
, “Development of a Two-Wheeled Mobile Tilting & Balancing (MTB) Robot
,” Proceedings of 11th International Conference on Control, Automation and Systems (ICCAS)/Robot World Conference
, South Korea
, Oct. 26–29
, IEEE, pp. 1-6
.45.
Tang
, H.
, Zhang
, J.
, Pan
, L.
, and Zhang
, D.
, 2023
, “Optimum Design for a New Reconfigurable Two-Wheeled Self-Balancing Robot Based on Virtual Equivalent Parallel Mechanism
,” ASME J. Mech. Des.
, 145
(5
), p. 053302
. 46.
Kong
, X.
, and Gosselin
, C.
, 2007
, Type Synthesis of Parallel Mechanisms
, Springer
, Netherlands
.47.
Dai
, J. S.
, 2012
, “Finite Displacement Screw Operators With Embedded Chasles' Motion
,” ASME J. Mech. Rob.
, 4
(4
), p. 041002
. 48.
Chai
, W.
, and Chen
, Y.
, 2010
, “The Line-Symmetric Octahedral Bricard Linkage and Its Structural Closure
,” Mech. Mach. Theory
, 45
(5
), pp. 772
–779
. 
