...Huixiang Hu; Xiaozhe Hong; Yan Gao Austenitic stainless steel is a widely used engineering material in industry and daily life due to its excellent corrosion resistance. The construction of superhydrophobic structure on stainless steel can endow it with special wetting properties and open up new...

...Weng-Sing Hwang; Tian-I Wu; Wen-Chung Sung The effects of postrolling heat treatment on the mechanical property and microstructure of 1050 aluminum alloy and 304 stainless steel (SS) clad metals were investigated. Clad metals were made by cold rolling after surface treatments of both sheets...

...S. Nakhodchi; B. G. Thomas; D. J. Smith Residual stresses in a stainless steel vessel containing glass have been evaluated using measurements and numerical simulation. High-level nuclear wastes are often vitrified in glass cast in cylindrical stainless steel containers. Knowledge of the internal...

...M. Barletta This study investigates the effectiveness of fluidized bed peening (FBP) to improve the fatigue behavior of axial-symmetric stainless steel substrates. The substrates were rotated at moderate speed inside a fluidized bed of stainless steel media. Their fatigue failure was determined...

...M. E. Kassner; P. Geantil; R. S. Rosen This study reports the significant ambient temperature creep plasticity at stresses below the conventional 0.2% plastic strain off-set yield stress. This is partially due to the relatively high strain-rate sensitivity of 304 stainless steel. Cold-working...

...Volkan Eskizeybek; Ahmet Avci; Ahmet Akdemir; Ömer Sinan Şahin Fatigue crack growth and related damage mechanisms were investigated experimentally in a stainless steel/aluminum laminated composite with middle through thickness crack, and two different fracture mechanics approaches applied...

...Alberto Polar; J. E. Indacochea; M. L. Wang The creep evolution was followed by conducting magnetic measurements on ferromagnetic steel samples exposed to different creep strains at a constant temperature. 410 stainless steel (410 SS) rods were submitted to creep at 625 ° C applying a constant...

... ranging from 1 μ m to 10 μ m on stainless steel, titanium, and aluminum. The results indicate that the geometrical characteristics of the interference patterns as well as the thermal properties of the substrates determine the quality of the fabricated structures. In particular, the best structures were...

...Julie Colin; Ali Fatemi; Said Taheri This paper discusses cyclic deformation and fatigue behaviors of stainless steel 304L and aluminum 7075-T6. Effects of loading sequence, mean strain or stress, and prestraining were investigated. The behavior of aluminum is shown not to be affected by preloading...

... process. The modified cam-clay model was used to describe the constitutive equation of porous stainless-steel SLS components. The densification process of SLS porous components was simulated using the finite element method. The visual distributions of shape change, displacement, density, and stress were...

... to variations in Δ ) have been reported for the AISI 420 stainless steel. Strain path affects the work hardening of metals during sheet forming, where some materials harden more and others less than under pure tension, for the same strain path. The present paper analyses the possibility that a similar...

... and then fabricated, modeled, and experimentally validated. To provide a unique biaxial stress state, a 60 mm diameter 10 mm thick disk of 316L stainless steel was plastically compressed through the thickness with an opposing 15 mm diameter hard steel indenters in the center of the disk. For validation, the stresses...

.... The point of the slope change is defined as the fatigue life of the specimen. The cyclic softening behavior of AL6XN distinguishes this alloy from the 300-series stainless steels. In the case of the metastable steels (for instance, 304 or 316), cyclic softening is followed by cyclic hardening, which...

...Jae-Hyung Cho; Paul R. Dawson Texture evolution during friction stir welding of stainless steel was investigated using a polycrystal plasticity model together with a three-dimensional, thermomechanically coupled, finite element formulation. The influence of frictional conditions with the tool pin...

...A. Gironès; M. Anglada; A. Mateo The corrosion fatigue performance of a superduplex stainless steel in two different chloride-bearing solutions ( 30 g ∕ l and 60 g ∕ l NaCl ) is explored in the present paper. Fatigue life results and surface damage analysis show a strong influence of the applied...

... conditions. These materials were AISI H13 tool steel, AISI 316L stainless steel, AISI 52100 hardened steel, and AISI 4340 steel. The Johnson–Cook (J–C) constitutive equation was used to model the plastic behavior of the workpiece material. Different values were assigned to the J-C parameters representing...

... the effective stresses and effective strains under a biaxial stress state. Annealed AA6011 aluminum tubes and SUS409 stainless-steel tubes were used for the bulge test. The tube thickness at the pole, bulge height, and the internal forming pressure were measured simultaneously during the bulge test...

...Sumantra Mandal; P. V. Sivaprasad; S. Venugopal A model is developed to predict the constitutive flow behavior of as cast 304 stainless steel during hot deformation using artificial neural network (ANN). The inputs of the neural network are strain, strain rate, and temperature, whereas flow stress...

... 26, 2003; revision received September 9, 2004. Review conducted by: M. F. Horstemeyer. 26 December 2003 09 September 2004 22 02 2005 stainless steel tool steel hardness hardness testing indentation work hardening elastic moduli yield strength tensile testing finite...

... MATERIALS AND TECHNOLOGY . Manuscript received by the Materials Division July 21, 2003; revision received February 26, 2004. Associate Editor: S. Mall. 21 July 2003 26 February 2004 09 11 2004 stainless steel internal stresses stress corrosion cracking corrosion resistance...