Graphical Abstract Figure
Graphical Abstract Figure
Close modal

Abstract

In this study, the welding of dissimilar aluminum alloys, Al 7075 and Al 6061, was investigated using Al 5356 filler rods reinforced with ZrB2 particles. The welding process was conducted using tungsten inert gas (TIG) welding, with and without ultrasonic vibration, to enhance weld quality and reduce hot cracking. Optimization of process parameters for dissimilar TIG welding was performed through Response Surface Methodology (RSM), which generated a design matrix to analyze the influence of process parameters on response variables. Numerical and graphical optimization was applied to minimize hot cracking sensitivity and maximize microhardness. The RSM-based models suggested an optimal welding current of 93 A, the use of Al 5356/ZrB2 nanocomposite filler, and the application of ultrasonic vibrations. Experimental validation of the identified solution demonstrated improvements in weld quality, including increased yield strength and ductility. The combination of nano-reinforced fillers and ultrasonic vibrations was found to enhance weldability and mitigate hot cracking in dissimilar aluminum joints. The mechanism of hot cracking reduction involved grain refinement, degassing, and homogenization due to ultrasonic vibrations, as well as the modification of weld pool chemistry and control of dilution by the nanocomposite filler, which collectively minimized solidification shrinkage and stress. Under these optimized conditions, no hot cracking was observed experimentally.

References

1.
Miller
,
W. S.
,
Zhuang
,
L.
,
Bottema
,
J.
,
Wittebrood
,
A.
,
De Smet
,
P.
,
Haszler
,
A.
, and
Vieregge
,
A. J. M. S.
,
2000
, “
Recent Development in Aluminium Alloys for the Automotive Industry
,”
Mater. Sci. Eng. A
,
280
(
1
), pp.
37
49
.
2.
Heinz
,
A.
,
Haszler
,
A.
,
Keidel
,
C.
,
Moldenhauer
,
S.
,
Benedictus
,
R.
, and
Miller
,
W. S.
,
2000
, “
Recent Development in Aluminium Alloys for Aerospace Applications
,”
Mater. Sci. Eng. A
,
280
(
1
), pp.
102
107
.
3.
Wahid
,
M. A.
,
Siddiquee
,
A. N.
, and
Khan
,
Z. A.
,
2020
, “
Aluminum Alloys in Marine Construction: Characteristics, Application, and Problems From a Fabrication Viewpoint
,”
Mar. Syst. Ocean Technol.
,
15
(
1
), pp.
70
80
.
4.
Bodunrin
,
M. O.
,
Alaneme
,
K. K.
, and
Chown
,
L. H.
,
2015
, “
Aluminium Matrix Hybrid Composites: A Review of Reinforcement Philosophies; Mechanical, Corrosion and Tribological Characteristics
,”
J. Mater. Res. Technol.
,
4
(
4
), pp.
434
445
.
5.
Sambathkumar
,
M.
,
Gukendran
,
R.
,
Mohanraj
,
T.
,
Karupannasamy
,
D. K.
,
Natarajan
,
N.
, and
Christopher
,
D. S.
,
2023
, “
A Systematic Review on the Mechanical, Tribological, and Corrosion Properties of Al 7075 Metal Matrix Composites Fabricated Through Stir Casting Process
,”
Adv. Mater. Sci. Eng.
,
2023
(
1
), p.
5442809
.
6.
Chelladurai
,
S. J. S.
,
Kumar
,
S. S.
,
Venugopal
,
N.
,
Ray
,
A. P.
,
Manjunath
,
T. C.
, and
Gnanasekaran
,
S.
,
2021
, “
A Review on Mechanical Properties and Wear Behaviour of Aluminium Based Metal Matrix Composites
,”
Mater. Today: Proc.
,
37
(
Part 2
), pp.
908
916
.
7.
Dorward
,
R. C.
, and
Pritchett
,
T. R.
,
1988
, “
Advanced Aluminium Alloys for Aircraft and Aerospace Applications
,”
Mater. Des.
,
9
(
2
), pp.
63
69
.
8.
Dhanaraj
,
P. S.
, and
Rathinasuriyan
,
C.
,
2022
, “
Optimization of Fiber Laser Welding Parameters for High Strength Aluminium Alloy AA7075-T6
,”
Mater. Today: Proc.
,
52
(
Part 3
), pp.
283
289
.
9.
Ke
,
W.
,
Zeng
,
Z.
,
Oliveira
,
J. P.
,
Peng
,
B.
,
Shen
,
J.
,
Tan
,
C.
,
Song
,
X.
, and
Yan
,
W.
,
2023
, “
Heat Transfer and Melt Flow of Keyhole, Transition and Conduction Modes in Laser Beam Oscillating Welding
,”
Int. J. Heat Mass Transfer
,
203
, p.
123821
.
10.
Liu
,
Y.
,
Wang
,
X.
,
Oliveira
,
J. P.
,
He
,
J.
, and
Guan
,
X.
,
2023
, “
Spatial and Directional Characterization of Wire and arc Additive Manufactured Aluminum Alloy Using Phased Array Ultrasonic Backscattering Method
,”
Ultrasonics
,
132
, p.
107024
.
11.
Jafari
,
H.
,
Mansouri
,
H.
, and
Honarpisheh
,
M.
,
2019
, “
Investigation of Residual Stress Distribution of Dissimilar Al-7075-T6 and Al-6061-T6 in the Friction Stir Welding Process Strengthened with SiO2 Nanoparticles
,”
J. Manuf. Processes
,
43
(
Part A
), pp.
145
153
.
12.
Seshu Kumar
,
G. S. V.
,
Kumar
,
A.
,
Rajesh
,
S.
,
Chekuri
,
R. B. R.
, and
Ramakotaiah
,
K.
,
2023
, “
An Experimental Study and Parameter Optimization of FSW for Welding Dissimilar 6061 and 7075 Al Alloys
,”
Int. J. Interact. Des. Manuf.
,
17
(
1
), pp.
215
223
.
13.
Mukhopadhyay
,
V.
, and
Sorokach
,
M. R.
,
2015
, “
Composite Structure Modeling and Analysis of Advanced Aircraft Fuselage Concepts
,”
Proceedings of the AIAA Modeling and Simulation Technologies Conference
,
Dallas, TX
,
June 22–26
, p.
3096
.
14.
Kloska
,
T.
, and
Fang
,
X.
,
2021
, “
Lightweight Chassis Components—The Development of a Hybrid Automotive Control Arm From Design to Manufacture
,”
Int. J. Automot. Technol.
,
22
(
5
), pp.
1245
1255
.
15.
Hosseinabadi
,
O. F.
, and
Khedmati
,
M. R.
,
2021
, “
A Review on Ultimate Strength of Aluminium Structural Elements and Systems for Marine Applications
,”
Ocean Eng.
,
232
, p.
109153
.
16.
Lin
,
C. C.
,
Huang
,
S. J.
, and
Liu
,
C. C.
,
2017
, “
Structural Analysis and Optimization of Bicycle Frame Designs
,”
Adv. Mech. Eng.
,
9
(
12
), p.
1687814017739513
.
17.
Sundaram
,
S. K.
, and
Bharath
,
A. G.
,
2022
, “
Influence of Target Dynamics and Number of Impacts on Ballistic Performance of 6061-T6 and 7075-T6 Aluminum Alloy Targets
,”
Mech. Based Des. Struct. Mach.
,
50
(
3
), pp.
993
1011
.
18.
Patel
,
V.
,
Li
,
W.
,
Wang
,
G.
,
Wang
,
F.
,
Vairis
,
A.
, and
Niu
,
P.
,
2019
, “
Friction Stir Welding of Dissimilar Aluminum Alloy Combinations: State-of-the-Art
,”
Metals
,
9
(
3
), p.
270
.
19.
Bindu
,
A. H.
,
Chaitanya
,
B. S. K.
,
Ajay
,
K.
, and
Sudhakar
,
I.
,
2020
, “
Investigation on Feasibility of Dissimilar Welding of AA2124 and AA7075 Aluminium Alloy Using Tungsten Inert Gas Welding
,”
Mater. Today: Proc.
,
26
(
Part 2
), pp.
2283
2288
.
20.
Çam
,
G.
, and
Koçak
,
M.
,
1998
, “
Progress in Joining of Advanced Materials
,”
Int. Mater. Rev.
,
43
(
1
), pp.
1
44
.
21.
Yang
,
J.
,
Oliveira
,
J. P.
,
Li
,
Y.
,
Tan
,
C.
,
Gao
,
C.
,
Zhao
,
Y.
, and
Yu
,
Z.
,
2022
, “
Laser Techniques for Dissimilar Joining of Aluminum Alloys to Steels: A Critical Review
,”
J. Mater. Process. Technol.
,
301
, p.
117443
.
22.
Starke
,
E. A.
Jr
, and
Staley
,
J. T.
,
1996
, “
Application of Modern Aluminum Alloys to Aircraft
,”
Prog. Aerosp. Sci.
,
32
(
2–3
), pp.
131
172
.
23.
Mvola
,
B.
,
Kah
,
P.
,
Martikainen
,
J.
, and
Suoranta
,
R.
,
2015
, “
State-of-the-Art of Advanced Gas Metal Arc Welding Processes: Dissimilar Metal Welding
,”
Proc. Inst. Mech. Eng. B
,
229
(
10
), pp.
1694
1710
.
24.
Derbiszewski
,
B.
,
Obraniak
,
A.
,
Rylski
,
A.
,
Siczek
,
K.
, and
Wozniak
,
M.
,
2024
, “
Studies on the Quality of Joints and Phenomena Therein for Welded Automotive Components Made of Aluminum Alloy—A Review
,”
Coatings
,
14
(
5
), p.
601
.
25.
Guzmán
,
I.
,
Granda
,
E.
,
Acevedo
,
J.
,
Martínez
,
A.
,
Dávila
,
Y.
, and
Velázquez
,
R.
,
2019
, “
Comparative in Mechanical Behavior of 6061 Aluminum Alloy Welded by Pulsed GMAW With Different Filler Metals and Heat Treatments
,”
Materials
,
12
(
24
), p.
4157
.
26.
Jiangang
,
P.
,
Bo
,
Y.
,
Jinguo
,
G.
,
Liang
,
Z.
, and
Hao
,
L.
,
2022
, “
Influence of Arc Mode on the Microstructure and Mechanical Properties of 5356 Aluminum Alloy Fabricated by Wire Arc Additive Manufacturing
,”
J. Mater. Res. Technol.
,
20
, pp.
1893
1907
.
27.
Nampoothiri
,
J.
,
Harini
,
R. S.
,
Nayak
,
S. K.
,
Raj
,
B.
, and
Ravi
,
K. R.
,
2016
, “
Post In-Situ Reaction Ultrasonic Treatment for Generation of Al–4.4 Cu/TiB2 Nanocomposite: A Route to Enhance the Strength of Metal Matrix Nanocomposites
,”
J. Alloys Compd.
,
683
, pp.
370
378
.
28.
Ramkumar
,
K. R.
, and
Natarajan
,
S.
,
2019
, “
Optimization of GTAW Al 3003 Weld Using Fabricated Nanocomposite Filler Metal
,”
Mater. Manuf. Processes
,
34
(
3
), pp.
293
302
.
29.
Bayati
,
M. S.
,
Sharifi
,
H.
,
Tayebi
,
M.
, and
Isfahani
,
T.
,
2019
, “
Effect of Al-B4C Nanocomposite Filler Manufactured by Accumulative Roll Bonding (ARB) Method on the Microstructure and Mechanical Properties of Weldings Prepared by Tungsten Inert gas Welding
,”
Mater. Res. Express
,
6
(
10
), p.
106529
.
30.
Murali
,
N.
, and
Li
,
X.
,
2021
, “
TIG Welding of Dissimilar High-Strength Aluminum Alloys 6061 and 7075 With Nano-Treated Filler Wires
,”
Proceedings of the Light Metals 2021: 50th Anniversary Edition
,
Springer International Publishing
, pp.
316
322
.
31.
Olayil
,
R.
,
Arumugaprabu
,
V.
,
Das
,
O.
, and
Anselm
,
W. L.
,
2021
, “
A Brief Review on Effect of Nano Fillers on Performance of Composites
,”
IOP Conf. Ser.: Mater. Sci. Eng.
,
1059
(
1
), p.
012006
.
32.
Bhat
,
A.
,
Budholiya
,
S.
,
Aravind Raj
,
S.
,
Sultan
,
M. T. H.
,
Hui
,
D.
,
Md Shah
,
A. U.
, and
Safri
,
S. N. A.
,
2021
, “
Review on Nanocomposites Based on Aerospace Applications
,”
Nanotechnol. Rev.
,
10
(
1
), pp.
237
253
.
33.
Fattahi
,
M.
,
Ghaheri
,
A.
,
Arabian
,
N.
,
Amirkhanlu
,
F.
, and
Moayedi
,
H.
,
2020
, “
Applying the Ultrasonic Vibration During TIG Welding as a Promising Approach for the Development of Nanoparticle Dispersion Strengthened Aluminum Weldments
,”
J. Mater. Process. Technol.
,
282
, p.
116672
.
34.
Annamalai
,
D.
,
Nampoothiri
,
J.
,
Manikandan Rajam
,
P. K.
, and
Radhakrishnan
,
H. K.
,
2023
, “
Optimization of Ultrasonic-Assisted TIG (UA-TIG) Welding Process Parameters for AA7075 Alloy Joints Using RSM-GA Approach
,”
J. Test. Eval.
,
51
(
5
), pp.
3369
3389
.
35.
Yuan
,
T.
,
Kou
,
S.
, and
Luo
,
Z.
,
2016
, “
Grain Refining by Ultrasonic Stirring of the Weld Pool
,”
Acta Mater.
,
106
, pp.
144
154
.
36.
Yuan
,
D.
,
Shao
,
S.
,
Guo
,
C.
,
Jiang
,
F.
, and
Wang
,
J.
,
2021
, “
Grain Refining of Ti-6Al-4V Alloy Fabricated by Laser and Wire Additive Manufacturing Assisted With Ultrasonic Vibration
,”
Ultrason. Sonochem.
,
73
, p.
105472
.
37.
Kumar
,
S.
,
Wu
,
C. S.
,
Padhy
,
G. K.
, and
Ding
,
W.
,
2017
, “
Application of Ultrasonic Vibrations in Welding and Metal Processing: A Status Review
,”
J. Manuf. Processes
,
26
(
April 2017
), pp.
295
322
.
38.
Wang
,
T.
,
Mazánová
,
V.
, and
Liu
,
X.
,
2022
, “
Ultrasonic Effects on Gas Tungsten Arc Based Wire Additive Manufacturing of Aluminum Matrix Nanocomposite
,”
Mater. Des.
,
214
, p.
110393
.
39.
Mohamed
,
O. A.
,
Masood
,
S. H.
, and
Bhowmik
,
J. L.
,
2015
, “
Optimization of Fused Deposition Modeling Process Parameters: A Review of Current Research and Future Prospects
,”
Adv. Manuf.
,
3
(
1
), pp.
42
53
.
40.
Gokul
,
R. R.
,
Lakshmanan
,
A.
, and
Nampoothiri
,
J.
,
2024
, “
Process Parameter Optimization of Ultrasonic Assisted TIG Welding of Al 7075 and Al 6061Alloy Joints
,”
Proceedings of the International Conference on Advancements in Materials, Design and Manufacturing for Sustainable Development, ICAMDMS 2024, EAI
,
Coimbatore, India
,
Feb. 23–24
, pp.
1
11
.
41.
Devanathan
,
C.
,
Elil Raja
,
D.
,
Sonar
,
T.
, and
Ivanov
,
M.
,
2024
, “
Effect of Friction Coefficient in Friction Stir Welding of B4C Reinforced AA5083 Metal Matrix Composites and Use of Fuzzy Clustering Technique for Weld Strength Prediction
,”
Adv. Mater. Sci. Eng.
,
2024
(
1
), p.
9880686
.
42.
Annamalai
,
D.
, and
Nampoothiri
,
J.
,
2024
, “
Ultrasonic-Assisted Tungsten Inert Gas Welding of Inconel 625 Joints to Reduce Hot Cracking and Improve Microhardness: Optimization and Prediction Methods
,”
J. Test. Eval.
,
52
(
4
), pp.
2515
2537
.
43.
Ghosh
,
A.
,
Mandal
,
S.
,
Nandi
,
G.
, and
Pal
,
P. K.
,
2018
, “
Metaheuristic Based Parametric Optimization of TIG Welded Joint
,”
Trans. Indian Inst. Met.
,
71
, pp.
1963
1973
.
44.
Khalfallah
,
F.
,
Boumerzoug
,
Z.
,
Rajakumar
,
S.
, and
Raouache
,
E.
,
2020
, “
Optimization by RSM on Rotary Friction Welding of AA1100 Aluminum Alloy and Mild Steel
,”
Int. Rev. Appl. Sci. Eng.
,
11
(
1
), pp.
34
42
.
45.
Mehdi
,
H.
, and
Mishra
,
R. S.
,
2022
, “
An Experimental Analysis and Optimization of Process Parameters of AA6061 and AA7075 Welded Joint by TIG+ FSP Welding Using RSM
,”
Adv. Mater. Process. Technol.
,
8
(
1
), pp.
598
620
.
46.
Joseph
,
J.
, and
Muthukumaran
,
S.
,
2017
, “
Optimization of Activated TIG Welding Parameters for Improving Weld Joint Strength of AISI 4135 PM Steel by Genetic Algorithm and Simulated Annealing
,”
Int. J. Adv. Manuf. Technol.
,
93
(
1–4
), pp.
23
34
.
47.
Pramod
,
S. L.
,
Bakshi
,
S. R.
, and
Murty
,
B. S.
,
2015
, “
Aluminum-Based Cast In Situ Composites: A Review
,”
J. Mater. Eng. Perform.
,
24
(
6
), pp.
2185
2207
.
You do not currently have access to this content.