1-18 of 18
Keywords: hardness
Close
Sort by
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. October 2021, 143(10): 101009.
Paper No: MANU-20-1161
Published Online: May 7, 2021
...T. Roy; A. Sharma; P. Ranjan; R. Balasubramaniam Electrical discharge machined surfaces inherently possess recast layer on the surface with heat affected zone (HAZ) beneath it and these have a detrimental effect on the mechanical properties viz., hardness, elastic modulus, etc. It is very difficult...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Manuf. Sci. Eng. November 2017, 139(11): 111010.
Paper No: MANU-17-1451
Published Online: September 13, 2017
...-hardened stainless steels. In the present study, effect of different heat treatment processes, namely solution annealing, aging, and overaging, on tensile strength, hardness, and wear properties has been studied in detail. Suitable metallurgical and mechanical characterization techniques have been applied...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Manuf. Sci. Eng. December 2012, 134(6): 061003.
Published Online: November 1, 2012
... drills when compared with untreated drills. These improvements were mainly attributed to formation of fine and homogeneous carbide particles and transformation of retained austenite to martensite. Microhardness and microstructure observations verified these formations. microstructure hardness...
Journal Articles
Publisher: ASME
Article Type: Design Innovations
J. Manuf. Sci. Eng. February 2012, 134(1): 015001.
Published Online: January 11, 2012
... temperatures under 1 MPa dynamic pressure of contact. The influence of different bonding temperatures on the microstructure, microindentation hardness, joint strength, and interlayer thickness has been studied. Additionally, a simple numerical model was developed to predict the evolution of interlayer during...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. June 2008, 130(3): 031008.
Published Online: May 6, 2008
... of ceramics. The LWJ process also improved the surface finish while reducing energy losses in the process. The practical realization of the LWJ manufacturing process could be a potential alternative to diamond saw, high-power laser, and high-pressure abrasive water-jet methods for machining hard and brittle...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Manuf. Sci. Eng. December 2007, 129(6): 1028–1034.
Published Online: March 13, 2007
... diagram. The ferritic and martensitic transformation as well as austenitization and tempering of martensite are considered. The influence of processing parameters such as laser power and traverse speed on the phase transformation and the consequent hardness are analyzed. The potential presence of porosity...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Manuf. Sci. Eng. April 2007, 129(2): 296–302.
Published Online: September 28, 2006
...K. Fathima; M. Rahman; A. Senthil Kumar; H. S. Lim The electrolytic in-process dressing (ELID) grinding is a new and an efficient process for ultra-precision finishing of hard and brittle materials. Unlike conventional grinding processes, the ELID grinding is a hybrid process that consists...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Manuf. Sci. Eng. August 2004, 126(3): 445–450.
Published Online: September 7, 2004
... are reviewed. Using an instrumented drilling-based test-bed, the effects of lubricating component depletion, microfiltration, and dilutant water hardness were assessed. It was observed that microfiltration had no effect on fluid functionality. Increases in dilutant water hardness were found to produce...
Journal Articles
Publisher: ASME
Article Type: Technical Briefs
J. Manuf. Sci. Eng. August 2004, 126(3): 637–639.
Published Online: September 7, 2004
... of microstructure and hardness of the fabricated Ni-nanoparticles dispersed H13 steel gear-shaped molds. Koch, C. C., 2002, Nanostructured Materials: Processing, Properties, and Potential Applications , Noyes Publications, New York. Goldstein, A. N., 1997, Handbook of Nanophase Materials , Marcel Dekker...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Manuf. Sci. Eng. February 2004, 126(1): 18–24.
Published Online: March 18, 2004
... characterization of shock treated copper thin films on single-crystal silicon substrates, where scanning x-ray microtopography is used to map the relative variation of the stress/strain field with micron spatial resolution, and instrumented nanoindentation is applied to measure the distribution of hardness...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Manuf. Sci. Eng. August 2002, 124(3): 588–594.
Published Online: July 11, 2002
... of workpiece hardness and cutting speed on chip formation, workpiece surface integrity and cutting forces. Equations are detailed for determining the primary shear zone temperature, the proportion of heat conducted into the workpiece and the shear flow stress. Following on from this, experimental work...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Manuf. Sci. Eng. August 2002, 124(3): 528–535.
Published Online: July 11, 2002
... towards the free surface. Depending on the work material hardness and cutting conditions, catastrophic failure within the upper region of the primary shear zone occurs through either ductile fracture or large strain plastic deformation. Prior to the onset of chip segmentation, which occurs with increases...
Journal Articles
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Manuf. Sci. Eng. November 2000, 122(4): 620–631.
Published Online: November 1, 1999
... based on the integrity of the surface produced. 2) Unlike case hardened steel, “saw toothed” chips will only be formed during hard turning of D 2 tool steel when the cutting pressure exerted in the direction of the cutting speed exceeds a value of approximately 4000 MPa. 3...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Manuf. Sci. Eng. August 2000, 122(3): 406–412.
Published Online: October 1, 1999
...Ge´rard Poulachon; Alphonse L. Moisan A 100Cr6 (AISI E52100) steel in the hardness range of 180 to 750 HV 10 was machined. Quick stop tests were carried out at various hardness values to observe the different chip formation mechanisms. A limit was found between the shearing and cracking chip...