Abstract

A critical problem in the underwater laser micromachining process is the optical disturbance caused by gas bubbles in water, where the laser beam quality and cut quality are significantly deteriorated. This paper introduces an acoustic streaming-assisted underwater laser ablation technique, where an ultrasonic transducer is positioned parallel to the workpiece surface. This configuration generates a cross-streaming water flow that effectively removes laser-induced debris and bubbles during the ablation in water. A pure titanium sheet was drilled by a nanosecond pulse laser subjected to acoustic streaming in a water chamber. A glass window for confining water and separating it from ambient air was recommended to minimize the optical disturbance caused by water waves. By using the proposed laser micro-drilling technique, a clean through-hole, small hole taper angle of as low as 6.8 deg, and minimal heat-affected zone (HAZ) were achievable compared to laser micro-drilling in air and in water without the assistance of acoustic streaming. The effects of laser power and drilling duration on hole dimensions and HAZ indicated that the hole entrance diameter increased from 270 µm at 10 W to 410 µm at 30 W, while the HAZ width expanded up to 128 µm only. Statistical analysis using ANOVA showed that laser power had a significant effect on the hole entrance and HAZ, whereas drilling duration had a minor impact. The proposed technique can thereby be an effective method for high-precision microscale machining with reduced thermal damage.

References

1.
Lv
,
J.
,
Dong
,
X.
,
Wang
,
K.
,
Duan
,
W.
,
Fan
,
Z.
, and
Mei
,
X.
,
2016
, “
Study on Process and Mechanism of Laser Drilling in Water and Air
,”
Int. J. Adv. Manuf. Technol.
,
86
(
5
), pp.
1443
1451
.
2.
Zhai
,
Z.
,
Wang
,
W.
,
Mei
,
X.
,
Wang
,
K.
,
Wang
,
F.
, and
Pan
,
A.
,
2018
, “
Effect of Temporal Control of Air/Water Environment on Laser Drilling of Nickel-Based Alloy With Thermal Barrier Coatings
,”
Int. J. Adv. Manuf. Technol.
,
97
(
9
), pp.
3395
3405
.
3.
Zhai
,
Z.
,
Wang
,
W.
,
Mei
,
X.
,
Wang
,
K.
, and
Yang
,
H.
,
2017
, “
Influence of Plasma Shock Wave on the Morphology of Laser Drilling in Different Environments
,”
Opt. Commun.
,
390
, pp.
49
56
.
4.
Canel
,
T.
,
Kaya
,
A. U.
, and
Çelik
,
B.
,
2012
, “
Parameter Optimization of Nanosecond Laser for Microdrilling on PVC by Taguchi Method
,”
Opt. Laser Technol.
,
44
(
8
), pp.
2347
2353
.
5.
Chen
,
Q.
,
Wang
,
H.-J.
,
Lin
,
D.-T.
,
Zuo
,
F.
,
Zhao
,
Z.-X.
, and
Lin
,
H.-T.
,
2018
, “
Characterization of Hole Taper in Laser Drilling of Silicon Nitride Ceramic Under Water
,”
Ceram. Int.
,
44
(
11
), pp.
13449
13452
.
6.
Charee
,
W.
, and
Tangwarodomnukun
,
V.
,
2018
, “
Dynamic Features of Bubble Induced by a Nanosecond Pulse Laser in Still and Flowing Water
,”
Opt. Laser Technol.
,
100
, pp.
230
243
.
7.
Tamura
,
A.
,
Sakka
,
T.
,
Fukami
,
K.
, and
Ogata
,
Y. H.
,
2013
, “
Dynamics of Cavitation Bubbles Generated by Multi-Pulse Laser Irradiation of a Solid Target in Water
,”
Appl. Phys. A: Mater. Sci. Process.
,
112
(
1
), pp.
209
213
.
8.
Nath
,
A.
, and
Khare
,
A.
,
2010
, “
Transient Evolution of Multiple Bubbles in Laser Induced Breakdown in Water
,”
Laser Part. Beams
,
29
(
1
), pp.
1
9
.
9.
Charee
,
W.
,
Tangwarodomnukun
,
V.
, and
Dumkum
,
C.
,
2016
, “
Ultrasonic-Assisted Underwater Laser Micromachining of Silicon
,”
J. Mater. Process. Technol.
,
231
, pp.
209
220
.
10.
Kruusing
,
A.
,
2004
, “
Underwater and Water-Assisted Laser Processing: Part 2—Etching, Cutting and Rarely Used Methods
,”
Opt. Lasers Eng.
,
41
(
2
), pp.
329
352
.
11.
Kruusing
,
A.
,
2004
, “
Underwater and Water-Assisted Laser Processing: Part 1—General Features, Steam Cleaning and Shock Processing
,”
Opt. Lasers Eng.
,
41
(
2
), pp.
307
327
.
12.
Nagarajan
,
B.
,
Wang
,
Z.
,
Castagne
,
S.
, and
Zheng
,
H.
,
2014
, “
Investigation of Laser-Induced Plasma Evolution in Flexible pad Laser Shock Forming With High Speed Camera
,”
Appl. Surf. Sci.
,
308
, pp.
221
229
.
13.
Zhou
,
J.
,
Xu
,
R.
,
Jiao
,
H.
,
Bao
,
J.
,
Liu
,
Q.
, and
Long
,
Y.
,
2020
, “
Study on the Mechanism of Ultrasonic-Assisted Water Confined Laser Micromachining of Silicon
,”
Opt. Lasers Eng.
,
132
, p.
106118
.
14.
Wang
,
H.
,
Zhu
,
S.
,
Asundi
,
A.
, and
Xu
,
Y.
,
2019
, “
Experimental Characterization of Laser Trepanning Performance Enhanced by Water-Based Ultrasonic Assistance
,”
Opt. Laser Technol.
,
109
, pp.
547
560
.
15.
Wang
,
H.
,
Zhu
,
S.
,
Xu
,
Y.
, and
Ren
,
N.
,
2019
, “
Experimental Investigation on Effects of Water-Based Ultrasonic Vibrations, Transverse Magnetic Field and Water Temperatures on Percussion Laser Drilling Performance
,”
Opt. Laser Technol.
,
112
, pp.
395
408
.
16.
Wang
,
H.
,
Xu
,
G.
,
Zhu
,
S.
,
Zhou
,
W.
,
Ren
,
N.
, and
Xia
,
K.
,
2018
, “
Comparison of Percussion Laser Drilling Quality With and Without Water-Based Ultrasonic Assistance
,”
J. Manuf. Process.
,
36
, pp.
175
180
.
17.
Wang
,
H.
,
Li
,
L.
,
Zhu
,
S.
,
Xu
,
Y.
, and
Ren
,
N.
,
2019
, “
Effect of Water-Based Ultrasonic Vibration on the Quality of Laser Trepanned Microholes in Nickel Super-Alloy Workpieces
,”
J. Mater. Process. Technol.
,
272
, pp.
170
183
.
18.
Sun
,
X.
,
Zhou
,
J.
,
Duan
,
J.-A.
,
Du
,
H.
,
Cui
,
D.
, and
Hu
,
Y.
,
2018
, “
Experimental Research on Ultrasound-Assisted Underwater Femtosecond Laser Drilling
,”
Laser Part. Beams
,
36
(
4
), pp.
487
493
.
19.
Liu
,
Z.
,
Wu
,
B.
,
Samanta
,
A.
,
Shen
,
N.
,
Ding
,
H.
,
Xu
,
R.
, and
Zhao
,
K.
,
2017
, “
Ultrasound-Assisted Water-Confined Laser Micromachining (UWLM) of Metals: Experimental Study and Time-Resolved Observation
,”
J. Mater. Process. Technol.
,
245
, pp.
259
269
.
20.
Tangwarodomnukun
,
V.
,
Likhitangsuwat
,
P.
,
Tevinpibanphan
,
O.
, and
Dumkum
,
C.
,
2015
, “
Laser Ablation of Titanium Alloy Under a Thin and Flowing Water Layer
,”
Int. J. Mach. Tools Manuf.
,
89
, pp.
14
28
.
21.
Wuttisarn
,
T.
,
Tangwarodomnukun
,
V.
, and
Dumkum
,
C.
,
2020
, “
Laser Micromachining of Titanium Alloy in Water and Ice at Different Temperatures
,”
Opt. Laser Technol.
,
125
, p.
106024
.
You do not currently have access to this content.