The use of gas bearings has increased over the past several decades to include microturbines, air cycle machines, and hermetically sealed compressors and turbines. Gas bearings have many advantages over traditional bearings, such as rolling element or oil lubricated fluid film bearings, including longer life, ability to use the process fluid, no contamination of the process with lubricants, accommodating high shaft speeds, and operation over a wide range of temperatures. Unlike fluid film bearings that utilize oil, gas lubricated bearings generate very little damping from the gas itself. Therefore, successful bearing designs such as foil bearings utilize damping features on the bearing to improve the damping generated. Similar to oil bearings, gas bearing designers strive to develop gas bearings with good rotordynamic stability. Gas bearings are challenging to design, requiring a fully coupled thermo-elastic, hydrodynamic analysis including complex nonlinear mechanisms such as Coulomb friction. There is a surprisingly low amount of rotordynamic force coefficient measurement in the literature despite the need to verify the model predictions and the stability of the bearing. This paper describes the development and testing of a 60,000 rpm gas bearing test rig and presents measured stiffness and damping coefficients for a 57 mm foil type bearing. The design of the rig overcomes many challenges in making this measurement by developing a patented, high-frequency, high-amplitude shaker system, resulting in excitation over most of the subsynchronous range.
Skip Nav Destination
Article navigation
October 2011
Research Papers
Development of a High Speed Gas Bearing Test Rig to Measure Rotordynamic Force Coefficients
J. Jeffrey Moore,
J. Jeffrey Moore
Southwest Research Institute®
, P.O. Box 28510, San Antonio, TX 78228-0510
Search for other works by this author on:
Andrew Lerche,
Andrew Lerche
Southwest Research Institute®
, P.O. Box 28510, San Antonio, TX 78228-0510
Search for other works by this author on:
Timothy Allison,
Timothy Allison
Southwest Research Institute®
, P.O. Box 28510, San Antonio, TX 78228-0510
Search for other works by this author on:
David L. Ransom,
David L. Ransom
Southwest Research Institute®
, P.O. Box 28510, San Antonio, TX 78228-0510
Search for other works by this author on:
Daniel Lubell
Daniel Lubell
Capstone Turbine Corporation
, 21211 Nordhoff Street, Chatsworth, CA 91311
Search for other works by this author on:
J. Jeffrey Moore
Southwest Research Institute®
, P.O. Box 28510, San Antonio, TX 78228-0510
Andrew Lerche
Southwest Research Institute®
, P.O. Box 28510, San Antonio, TX 78228-0510
Timothy Allison
Southwest Research Institute®
, P.O. Box 28510, San Antonio, TX 78228-0510
David L. Ransom
Southwest Research Institute®
, P.O. Box 28510, San Antonio, TX 78228-0510
Daniel Lubell
Capstone Turbine Corporation
, 21211 Nordhoff Street, Chatsworth, CA 91311J. Eng. Gas Turbines Power. Oct 2011, 133(10): 102504 (9 pages)
Published Online: May 6, 2011
Article history
Received:
May 10, 2010
Revised:
August 9, 2010
Online:
May 6, 2011
Published:
May 6, 2011
Citation
Moore, J. J., Lerche, A., Allison, T., Ransom, D. L., and Lubell, D. (May 6, 2011). "Development of a High Speed Gas Bearing Test Rig to Measure Rotordynamic Force Coefficients." ASME. J. Eng. Gas Turbines Power. October 2011; 133(10): 102504. https://doi.org/10.1115/1.4002865
Download citation file:
Get Email Alerts
Cited By
Temperature Dependence of Aerated Turbine Lubricating Oil Degradation from a Lab-Scale Test Rig
J. Eng. Gas Turbines Power
Multi-Disciplinary Surrogate-Based Optimization of a Compressor Rotor Blade Considering Ice Impact
J. Eng. Gas Turbines Power
Experimental Investigations on Carbon Segmented Seals With Smooth and Pocketed Pads
J. Eng. Gas Turbines Power
Related Articles
Rotordynamic Performance of Flexure Pivot Hydrostatic Gas Bearings for Oil-Free Turbomachinery
J. Eng. Gas Turbines Power (October,2007)
Identification of Rotordynamic Force Coefficients of a Metal Mesh Foil Bearing Using Impact Load Excitations
J. Eng. Gas Turbines Power (November,2011)
A New Analysis Tool Assessment for Rotordynamic Modeling of Gas Foil Bearings
J. Eng. Gas Turbines Power (February,2011)
Foil Gas Bearing With Compression Springs: Analyses and Experiments
J. Tribol (July,2007)
Related Proceedings Papers
Related Chapters
Summary and Conclusions
Bearing Dynamic Coefficients in Rotordynamics: Computation Methods and Practical Applications
Supporting Systems/Foundations
Handbook on Stiffness & Damping in Mechanical Design
Unbalance
Fundamentals of Rotating Machinery Diagnostics