Soot formation phenomenon is far from being fully understood today and models available for simulation of soot in practical combustion devices remain of relatively limited success, despite significant progresses made over the last decade. The extremely high demand of computing time of detailed soot models make them unrealistic for simulation of multidimensional, transient, and turbulent diesel engine combustion. Hence, most of the investigations conducted in real configuration such as multidimensional diesel engines simulation utilize coarse modeling, the advantages of which are an easy implementation and low computational cost. In this study, a phenomenological three-equation soot model was developed for modeling soot formation in diesel engine combustion based on considerations of acceptable computational demand and a qualitative description of the main features of the physics of soot formation. The model was developed based on that of Tesner et al. and was implemented into the commercial STAR-CD™ CFD package. Application of this model was demonstrated in the modeling of soot formation in a single-cylinder research version of Caterpillar 3400 series diesel engine with exhaust gas recirculation (EGR). Numerical results show that the new soot formulation overcomes most of the drawbacks in the existing soot models dedicated to this kind of engineering task and demonstrates a robust and consistent behavior with experimental observation. Compared to the existing soot models for engine combustion modeling, some distinct features of the new soot model include: no soot is formed at low temperature, minimal model parameter adjustment for application to different fuels, and there is no need to prescribe the soot particle size. At the end of expansion, soot is predicted to exist in two separate regions in the cylinder: in the near wall region and in the center part of the cylinder. The existence of soot in the near wall region is a result of reduced soot oxidation rate through heat loss. They are the source of the biggest primary particles released at the end of the combustion process. The center part of the cylinder is populated by smaller soot particles, which are created since the early stages of the combustion process but also subject to intense oxidation. The qualitative effect of EGR is to increase the size of soot particles as well as their number density. This is linked to the lower in-cylinder temperature and a reduced amount of air.

1.
Belardini
,
P.
,
Bertoli
,
C.
,
Ciajolo
,
A.
,
D’Anna
,
A.
, and
Del Giacomo
,
N.
, 1992, “
Three Dimensional Calculations of D. I. Diesel Engine Combustion and Comparison With in Cylinder Sampling Valve Data
,” SAE Technical Paper No. 92225.
2.
U. S. E. P. A.
(EPA), 2002, “
Air Quality Criteria for Particulate Matter
,” Third external review draft EPA/600/P-99/002aC, Research Triangle Park, NC.
3.
2001, “
Réduire les émissions des Véhicules / Vehicle Emission Reductions
,” 92-82-11363-9,
Proceedings of the European Conference of Ministers of Transport (ECMT)
,
OECD
,
Paris
.
4.
Khan
,
G.
, and
Greeves
,
A.
, 1974,
Method for Calculating the Formation and Combustion of Soot in Diesel Engines
,
Scripta
,
Washington, DC
, Chap. 25.
5.
Surovikin
,
V.
, 1976, “
Analytical Description of the Processes of Nucleus-Formation and Growth of Particles of Carbon Black in the Thermal Decomposition of Aromatic Hydrocarbons in the Gas Phase
,”
Solid Fuel Chem.
,
10
(
1
), pp.
92
101
.
6.
Fusco
,
A.
,
Knox-Kelecy
,
A.
, and
Foster
,
D.
, 1994, “
Application of a Phenomenological Soot Model to Diesel Engine Combustion
,”
Proceedings of the International Symposium COMODIA 94
,
Yokohama, Japan
.
7.
Appel
,
J.
,
Bockhorn
,
H.
, and
Frenklach
,
M.
, 2000, “
Kinetic Modeling of Soot Formation With Detailed Chemistry and Physics: Laminar Premixed Flames of C2 Hydrocarbons
,”
Combust. Flame
0010-2180,
121
(
1/2
), pp.
122
136
.
8.
Tao
,
F.
,
Golovitchev
,
V.
, and
Chomiak
,
J.
, 2004, “
A Phenomenological Model for the Prediction of Soot Formation in Diesel Spray Combustion
,”
Combust. Flame
0010-2180,
136
(
3
), pp.
270
282
.
9.
Ahmad
,
T.
,
Plee
,
S.
, and
Myers
,
J.
, 1985, “
Computation of Nitric Oxide and Soot Emissions from Turbulent Diffusion Flames
,”
J. Eng. Gas Turbines Power
0742-4795,
107
(
1
), pp.
48
53
.
10.
Hiroyasu
,
H.
, and
Nishida
,
K.
, 1989, “
Simplified Three-Dimensional Modeling of Mixture Formation and Combustion in D. I. Diesel Engine
,” SAE Technical Paper No. 890269.
11.
Patterson
,
M.
,
Kong
,
S.
,
Hampson
,
G.
, and
Reitz
,
R.
, 1994, “
Modeling the Effects of Fuel Injection Characteristics on Diesel Engine Soot and NOx Emissions
,” SAE Technical Paper No. 940523.
12.
Han
,
Z.
, and
Reitz
,
R.
, 1995, “
Turbulence Modeling of Internal Combustion Engines using RNG κ-ε Models
,”
Combust. Sci. Technol.
0010-2202,
106
(
4/6
), pp.
267
295
.
13.
Kong
,
S.
,
Han
,
Z.
, and
Reitz
,
R.
, 1995, “
The Development and Application of a Diesel Ignition and Combustion Model for Multidimensional Engine Simulation
,” SAE Technical Paper No. 950278.
14.
Reitz
,
R.
, and
Rutland
,
C.
, 1995, “
Development and Testing of Diesel Engine CFD models
,”
Prog. Energy Combust. Sci.
0360-1285,
21
(
2
), pp.
173
196
.
15.
Uludogan
,
A.
,
Xin
,
J.
, and
Reitz
,
R.
, 1996, “
Exploring the Use of Multiple Injectors and Split Injection to Reduce D. I. Diesel Engine Emissions
,” SAE Technical Paper No. 962058.
16.
Han
,
Z.
,
Uludogan
,
A.
,
Hampson
,
G.
, and
Reitz
,
R.
, 1996, “
Mechanism of Soot and NOx Emission Reduction Using Multiple-Injection in a Diesel Engine
,” SAE Technical Paper No. 960633.
17.
Chan
,
M.
,
Das
,
S.
, and
Reitz
,
R.
, 1997, “
Modeling Multiple Injection and EGR Effects on Diesel Engine Emissions
,” SAE Technical Paper No. 972864.
18.
Fuchs
,
T.
, and
Rutland
,
C.
, 1998, “
Intake Flow Effects on Combustion and Emissions in a Diesel Engine
,” SAE Technical Paper No. 980508.
19.
Das
,
S.
,
Houtz
,
P.
, and
Reitz
,
R.
, 1999, “
Effect of Injection Spray Angle and Combustion Chamber Geometry on Engine Performance and Emission Characteristics of a Large Bore Diesel Engine
,”
Proceedings of the Spring Technical Conference, ASME
, Vol.
32–1
, pp.
1
12
.
20.
Jung
,
D.
, and
Assanis
,
D.
, 2001, “
Multi-Zone DI Diesel Spray Combustion Model for Cycle Simulation Studies of Engine Performance and Emissions
,” SAE Technical Paper No. 2001-01-1246.
21.
Tesner
,
P.
,
Snegiriova
,
T.
, and
Knorre
,
V.
, 1971, “
Kinetics of Dispersed Carbon Formation
,”
Combust. Flame
0010-2180,
17
(
2
), pp.
253
260
.
22.
Mehler
,
R.
,
Amann
,
M.
, and
Schopp
,
W.
, 2002, “
A Methodology to Estimate Changes in Statistical Life Expectancy Due to the Control of Particulate Matter Air Pollution
,” Technical Report No. IR-02-035,
International Institute for Applied Systems Analysis
, Laxenburg, Austria.
23.
Parker
,
J.
, 2005, “
Air Pollution and Birth Weight among Term Infants in California
,”
Pediatrics
0031-4005,
115
(
1
), pp.
121
128
.
24.
Lee
,
J.
,
Goto
,
Y.
, and
Okada
,
M.
, 2002, “
Measurement of the Diesel Exhaust Particle Reduction Effect and Particle Size Distribution in a Transient Cycle Mode With an Installed Diesel Particulate Filter (DPF)
,” SAE Technical Paper No. 2002-01-1005.
25.
Moss
,
J.
,
Stewart
,
C.
, and
Young
,
K.
, 1995, “
Modeling Soot Formation and Burnout in a High Temperature Laminar Diffusion Flame Burning under Oxygen-Enriched Conditions
,”
Combust. Flame
0010-2180,
101
(
4
), pp.
491
500
.
26.
Leung
,
K.
,
Lindstedt
,
R.
, and
Jones
,
W.
, 1991, “
A Simplified Reaction Mechanism for Soot Formation in Nonpremixed Flames
,”
Combust. Flame
0010-2180,
87
(
3/4
), pp.
289
305
.
27.
Bédat
,
B.
,
Egolfopoulos
,
F. N.
, and
Poinsot
,
T.
, 1999, “
Direct Numerical Simulation of Heat Release and NOx Formation in Turbulent Nonpremixed Flames
,”
Combust. Flame
0010-2180,
119
(
1/2
), pp.
69
83
.
28.
Nagle
,
J.
, and
Strickland-Constable
,
R.
, 1962, “
Oxidation of Carbon Between 1000–2000°C
,”
Proceedings of the Fifth Conference on Carbon
,
Pergamon
,
London
, pp.
154
164
.
29.
Fenimore
,
C.
, and
Jones
,
G.
, 1967, “
Oxidation of Soot by Hydroxyl Radicals
,”
J. Phys. Chem.
0022-3654,
71
(
3
), pp.
593
597
.
30.
Bradley
,
D.
,
Dixon-Lewis
,
G.
,
El-Din Habik
,
S.
, and
Mushi
,
E.
, 1984, “
The Oxidation of Graphite Powder in Flame Reaction Zones
,”
Proceedings of the 20th International Symposium on Combustion
,
The Combustion Institute
,
Pittsburgh
, pp.
931
940
.
31.
Garo
,
A.
, 2004, private communication.
32.
Westbrook
,
C.
, and
Dryer
,
F.
, 1984, “
Chemical Kinetic Modelling of Hydrocarbon Combustion
,”
Prog. Energy Combust. Sci.
0360-1285,
10
(
1
), pp.
1
57
.
33.
Magnussen
,
B.
, and
Hjertager
,
B.
, 1976, “
On Mathematical Modeling of Turbulent Combustion With Special Emphasis on Soot Formation and Combustion
,”
Proceedings of the 16th International Symposium on Combustion
,
The Combustion Institute
,
Pittsburgh
, pp.
719
729
.
34.
Methodology volume, Star-CD, 2004, Edition.
35.
Huh
,
K.
, and
Gosman
,
A.
, 1991, “
A Phenomenological Model of Diesel Spray Atomisation
,”
Proceedings of the International Conference on Multiphase Flows (ICMF’91)
,
Tsukuba, Japan
.
36.
Reitz
,
R.
, and
Diwakar
,
R.
, 1986, “
Effect of Drop Breakup on Fuel Sprays
,” SAE Technical Paper No. 860469.
37.
Mastorakos
,
E.
, and
Wright
,
Y. M.
, 2003, “
Simulations of Turbulent Spray Auto-Ignition With Elliptic Conditional Moment Closure
,”
Proceedings of the European Combustion Meeting
,
Orléans, France
.
38.
Yakhot
,
V.
,
Orszag
,
S.
,
Thangam
,
S.
,
Gatski
,
T.
, and
Speziale
,
C.
, 1992, “
Development of Turbulence Models for Shear Flows by a Double Expansion Technique
,”
Phys. Fluids A
0899-8213,
4
(
7
), pp.
1510
1520
.
39.
Launder
,
B.
, and
Spalding
,
D.
, 1974, “
The Numerical Computation of Turbulent Flows
,”
Comput. Methods Appl. Mech. Eng.
0045-7825,
3
(
2
), pp.
269
289
.
40.
Jayatilleka
,
C.
, 1969, “
The Influence of Prandtl Number and Surface Roughness on the Resistance of the Laminar Sub-Layer to Momentum and Heat Transfer
,”
Prog. Heat Mass Transfer
0079-631X,
1
, pp.
193
330
.
41.
McLandress
,
A.
,
Emerson
,
R.
,
McDowell
,
P.
, and
Rutland
,
C.
, 1996, “
Intake and in-Cylinder Flow Modeling Characterization of Mixing and Comparison With Flow Bench Results
,” SAE Technical Paper No. 960635.
42.
Neill
,
W. S.
, and
Chippior
,
W.
, 2002, NRC Report No. PET-1528-02S.
43.
Hergart
,
C.
,
Barths
,
H.
, and
Peters
,
N.
, 2000, “
Using Representative Interactive Flamelets in Three-Dimensional Modelling of the Diesel Combustion Process Including Effects of Heat Transfer
,”
Proceedings of the International Multidimensional Engine Modeling User’s Group Meeting
,
Madison, WI
.
44.
Hergart
,
C.
, and
Peters
,
N.
, 2002, “
Applying the Representative Interactive Flamelet Model to Evaluate the Potential Effect of Wall Heat Transfer on Soot Emissions in a Small-Bore Direct-Injection Diesel Engine
,”
J. Eng. Gas Turbines Power
0742-4795,
124
(
4
), pp.
1042
1052
.
45.
Tao
,
F.
,
Srinivas
,
S.
,
Reitz
,
R. D.
, and
Foster
,
D. E.
, 2004, “
Current Status of Soot Modeling Applied to Diesel Combustion Simulations
,”
Proceedings of the International Symposium COMODIA 2004
,
Yokohama, Japan
.
46.
Khan
,
I. M.
,
Wang
,
C. H. T.
, and
Langridge
,
B. E.
, 1971, “
Coagulation and Combustion of Soot Particles in Diesel Engines
,”
Combust. Flame
0010-2180,
17
(
3
), pp.
408
419
.
47.
Smith
,
O. I.
, 1981, “
Fundamentals of Soot Formation in Flames With Application to Diesel Engine Particulate Emissions
,”
Prog. Energy Combust. Sci.
0360-1285,
7
(
4
), pp.
275
291
.
You do not currently have access to this content.