This paper presents a summary of the life prediction methods developed under the NASA Lewis Research Center’s Hot Section Technology (HOST) program. A major objective of the fatigue and fracture efforts under the HOST program was to significantly improve the analytic life prediction tools used by the aeronautical gas turbine engine industry. This has been achieved in the areas of high-temperature thermal and mechanical fatigue of bare and coated high-temperature superalloys. Such technical improvements will eventually reduce life cycle costs. The cyclic crack initiation and propagation resistance of nominally isotropic polycrystalline alloys and highly anisotropic single crystal alloys have been addressed. A sizeable data base has been generated for three alloys [cast PWA 1455 (B–1900 + Hf), wrought Inconel 718, and cast single-crystal PWA 1480] in bare and coated conditions. Two coating systems, diffusion aluminide (PWA 273) and plasma-sprayed MCrAlY overlay (PWA 286), were employed. Life prediction modeling efforts were devoted to creep-fatigue interaction, oxidation, coatings interactions, multiaxially of stress-strain states, mean stress effects, cumulative damage, and thermomechanical fatigue. The fatigue crack initiation life models developed to date include the Cyclic Damage Accumulation (CDA) Model of Pratt & Whitney and the Total Strain Version of Strainrange Partitioning (TS-SRP) of NASA Lewis for nominally isotropic materials, and the Tensile Hysteretic Energy Model of Pratt & Whitney for anisotropic superalloys. The fatigue model being developed by the General Electric Company is based upon the concepts of Path-Independent Integrals (PII) for describing cyclic crack growth under complex non-linear response at the crack tip due to thermomechanical loading conditions. A micromechanistic oxidation crack extension model has been derived by researchers at Syracuse University. The models are described and discussed in the paper. Only limited verification has been achieved to date as several of the technical programs are still in progress and the verification tasks are scheduled, quite naturally, near the conclusion of the program. To date, efforts have concentrated on developement of independent models for cyclic constitutive behavior, cyclic crack initiation, and cyclic crack propagation. The transition between crack initiation and crack propagation has not been thoroughly researched as yet, and the integration of these models into a unified life prediction method has not been addressed.
Skip Nav Destination
Article navigation
April 1989
Research Papers
Fatigue Life Prediction Modeling for Turbine Hot Section Materials
G. R. Halford,
G. R. Halford
NASA Lewis Reseach Center, Cleveland, OH 44135
Search for other works by this author on:
T. G. Meyer,
T. G. Meyer
United Technologies, Pratt and Whitney, East Hartford, CT 06108
Search for other works by this author on:
R. S. Nelson,
R. S. Nelson
United Technologies, Pratt and Whitney, East Hartford, CT 06108
Search for other works by this author on:
D. M. Nissley,
D. M. Nissley
United Technologies, Pratt and Whitney, East Hartford, CT 06108
Search for other works by this author on:
G. A. Swanson
G. A. Swanson
United Technologies, Pratt and Whitney, East Hartford, CT 06108
Search for other works by this author on:
G. R. Halford
NASA Lewis Reseach Center, Cleveland, OH 44135
T. G. Meyer
United Technologies, Pratt and Whitney, East Hartford, CT 06108
R. S. Nelson
United Technologies, Pratt and Whitney, East Hartford, CT 06108
D. M. Nissley
United Technologies, Pratt and Whitney, East Hartford, CT 06108
G. A. Swanson
United Technologies, Pratt and Whitney, East Hartford, CT 06108
J. Eng. Gas Turbines Power. Apr 1989, 111(2): 279-285 (7 pages)
Published Online: April 1, 1989
Article history
Received:
November 16, 1987
Online:
October 15, 2009
Citation
Halford, G. R., Meyer, T. G., Nelson, R. S., Nissley, D. M., and Swanson, G. A. (April 1, 1989). "Fatigue Life Prediction Modeling for Turbine Hot Section Materials." ASME. J. Eng. Gas Turbines Power. April 1989; 111(2): 279–285. https://doi.org/10.1115/1.3240249
Download citation file:
Get Email Alerts
Cited By
Image-based flashback detection in a hydrogen-fired gas turbine using a convolutional autoencoder
J. Eng. Gas Turbines Power
Fuel Thermal Management and Injector Part Design for LPBF Manufacturing
J. Eng. Gas Turbines Power
An investigation of a multi-injector, premix/micromix burner burning pure methane to pure hydrogen
J. Eng. Gas Turbines Power
Related Articles
Improved Performance Rhenium Containing Single Crystal Alloy Turbine Blades Utilizing PPM Levels of the Highly Reactive Elements Lanthanum and Yttrium
J. Eng. Gas Turbines Power (January,1999)
Aero Engine Test Experience With CMSX-4® Alloy Single-Crystal Turbine Blades
J. Eng. Gas Turbines Power (April,1996)
Biaxial Thermomechanical-Fatigue Life Property of a Directionally Solidified Ni-Base Superalloy
J. Eng. Gas Turbines Power (November,2008)
Reaction Diffusion Behaviors for Interface Between Ni-Based Super Alloys and Vacuum Plasma Sprayed MCrAlY Coatings
J. Eng. Gas Turbines Power (July,1999)
Related Proceedings Papers
Related Chapters
Introductory Information
The Stress Analysis of Cracks Handbook, Third Edition
Clinical issues and experience
Mechanical Blood Trauma in Circulatory-Assist Devices
Fatigue-Crack Propagation Through a Measured Residual Stress Field in Alloy Steel
Flaw Growth and Fracture