This paper aims to develop a three-dimensional (3D) measurement approach to investigate the flow structures of viscoelastic fluid in the curved microchannel by using digital holographic microscope (DHM). The measurement system uses off-axis holographic/interferometric optical setup for the moving target, and the real-time three-dimensional-three-components (3D3C) particle tracking velocimetry (PTV) can be achieved based on the analysis of phase information of holograms. To diagnose the irregular flow inside the microchannel, the 3D temporal positions of tracer particles in the volume of 282 μm × 282 μm × 60 μm have been detected and velocity field was calculated based on the PTV algorithm. Moreover, to explain the flow field inside the curved microchannel, for the first time the polarized high-speed camera was utilized to identify the strong elongation in the viscoelastic fluid. The DHM is proven to be successful for the measurements of microfluidic flow, especially for the truly real-time 3D motions.
Skip Nav Destination
Article navigation
September 2016
Research-Article
Measurement of Viscoelastic Fluid Flow in the Curved Microchannel Using Digital Holographic Microscope and Polarized Camera
Xiao-Bin Li,
Xiao-Bin Li
Mem. ASME
School of Energy Science and Engineering,
School of Mechatronics Engineering,
Harbin Institute of Technology,
Harbin 150001, China;
School of Energy Science and Engineering,
School of Mechatronics Engineering,
Harbin Institute of Technology,
Harbin 150001, China;
Institute of Industrial Science,
The University of Tokyo,
Tokyo 153-8505, Japan;
The University of Tokyo,
Tokyo 153-8505, Japan;
Key Laboratory of Efficient Utilization of Low and
Medium Grade Energy,
Tianjin University,
Ministry of Education of China,
Tianjin 300072, China
e-mail: lixb@hit.edu.cn
Medium Grade Energy,
Tianjin University,
Ministry of Education of China,
Tianjin 300072, China
e-mail: lixb@hit.edu.cn
Search for other works by this author on:
Masamichi Oishi,
Masamichi Oishi
Institute of Industrial Science,
The University of Tokyo,
Tokyo 153-8505, Japan
e-mail: oishi@iis.u-tokyo.ac.jp
The University of Tokyo,
Tokyo 153-8505, Japan
e-mail: oishi@iis.u-tokyo.ac.jp
Search for other works by this author on:
Marie Oshima,
Marie Oshima
Institute of Industrial Science,
The University of Tokyo,
Tokyo 153-8505, Japan
e-mail: marie@iis.u-tokyo.ac.jp
The University of Tokyo,
Tokyo 153-8505, Japan
e-mail: marie@iis.u-tokyo.ac.jp
Search for other works by this author on:
Feng-Chen Li
Feng-Chen Li
School of Energy Science and Engineering,
Harbin Institute of Technology,
Harbin 150001, China
e-mail: lifch@hit.edu.cn
Harbin Institute of Technology,
Harbin 150001, China
e-mail: lifch@hit.edu.cn
Search for other works by this author on:
Xiao-Bin Li
Mem. ASME
School of Energy Science and Engineering,
School of Mechatronics Engineering,
Harbin Institute of Technology,
Harbin 150001, China;
School of Energy Science and Engineering,
School of Mechatronics Engineering,
Harbin Institute of Technology,
Harbin 150001, China;
Institute of Industrial Science,
The University of Tokyo,
Tokyo 153-8505, Japan;
The University of Tokyo,
Tokyo 153-8505, Japan;
Key Laboratory of Efficient Utilization of Low and
Medium Grade Energy,
Tianjin University,
Ministry of Education of China,
Tianjin 300072, China
e-mail: lixb@hit.edu.cn
Medium Grade Energy,
Tianjin University,
Ministry of Education of China,
Tianjin 300072, China
e-mail: lixb@hit.edu.cn
Masamichi Oishi
Institute of Industrial Science,
The University of Tokyo,
Tokyo 153-8505, Japan
e-mail: oishi@iis.u-tokyo.ac.jp
The University of Tokyo,
Tokyo 153-8505, Japan
e-mail: oishi@iis.u-tokyo.ac.jp
Tsukasa Matsuo
Marie Oshima
Institute of Industrial Science,
The University of Tokyo,
Tokyo 153-8505, Japan
e-mail: marie@iis.u-tokyo.ac.jp
The University of Tokyo,
Tokyo 153-8505, Japan
e-mail: marie@iis.u-tokyo.ac.jp
Feng-Chen Li
School of Energy Science and Engineering,
Harbin Institute of Technology,
Harbin 150001, China
e-mail: lifch@hit.edu.cn
Harbin Institute of Technology,
Harbin 150001, China
e-mail: lifch@hit.edu.cn
1Corresponding author.
Contributed by the Fluids Engineering Division of ASME for publication in the JOURNAL OF FLUIDS ENGINEERING. Manuscript received September 14, 2015; final manuscript received March 10, 2016; published online June 6, 2016. Assoc. Editor: Shizhi Qian.
J. Fluids Eng. Sep 2016, 138(9): 091401 (8 pages)
Published Online: June 6, 2016
Article history
Received:
September 14, 2015
Revised:
March 10, 2016
Citation
Li, X., Oishi, M., Matsuo, T., Oshima, M., and Li, F. (June 6, 2016). "Measurement of Viscoelastic Fluid Flow in the Curved Microchannel Using Digital Holographic Microscope and Polarized Camera." ASME. J. Fluids Eng. September 2016; 138(9): 091401. https://doi.org/10.1115/1.4033319
Download citation file:
Get Email Alerts
Cited By
Effects of Tire Attributes on the Aerodynamic Performance of a Generic Car–Tire Assembly
J. Fluids Eng (January 2025)
Related Articles
1990 Max Jakob Memorial Award Lecture: Viscoelastic Fluids: A New Challenge in Heat Transfer
J. Heat Transfer (May,1992)
Effect of Gas/Liquid Shearing on the Viscoelastic Instability of a Planar Sheet
J. Fluids Eng (April,2017)
The Mechanism of Size-Based Particle Separation by Dielectrophoresis in the Viscoelastic Flows
J. Fluids Eng (September,2018)
Guest Editorial
J. Fluids Eng (March,2004)
Related Proceedings Papers
Related Chapters
Experiment Investigation of Flow Boiling Process Including Cavitation in Micro-Channel
Inaugural US-EU-China Thermophysics Conference-Renewable Energy 2009 (UECTC 2009 Proceedings)
Fluid Mechanics
Engineering Practice with Oilfield and Drilling Applications
Fluid Mechanics
Centrifugal Compressors: A Strategy for Aerodynamic Design and Analysis