In this paper, axial thrust problems of multistage pumps are presented. The entire investigation has been focused on the pump design concept having all impellers in series (facing in one direction) and is valid for barrel casing type as well as for segmental type. The major part of the investigation has been experimental on one stage testing arrangement, using also Laser Doppler Anemometry (LDA) for determination of fluid rotation in the impeller side chamber. Numerical flow analysis (NFA) has been applied for some flow variants in order to verify whether a numerical approach could simulate the test results. The phenomenon of fluid rotation in side chambers and its effect on impeller hydraulic axial thrust have been determined for different leakage flow regimes. The influence of increased wear ring radial clearance on axial thrust has been analyzed together with the solutions for pump hydraulic axial thrust reduction.

Issue Section:
Technical Papers
Keywords:
Multistage Pump, Axial Thrust, Impeller Side Chamber, Fluid Rotation, Static Pressure Distribution, pumps, hydraulic turbines, rotational flow, laser Doppler anemometry, flow simulation
Topics:
Flow (Dynamics), Fluids, Impellers, Pressure, Pumps, Rotation, Thrust, Wear, Design, Leakage flows
1.
Daily
,
J. W.
, and
Nece
,
R. E.
,
1960
, “
Chamber Dimension Effects on Induced Flow and Frictional Resistance of Enclosed Rotating Disks
,”
J. Basic Eng.
,
83
, pp.
217
–
232
.
2.
Kurokawa, J., and Toyokura, T., 1972, “Study on Axial Thrust of Radial Flow Turbomachinery,” Proceedings, The Second International JSME Symposium-Fluid Machinery and Fluidics, Tokyo, Japan, pp. 31–40.
3.
Iino
,
T.
,
Sato
,
H.
, and
Miyashiro
,
H.
,
1980
, “
Hydraulic Axial Thrust in Multistage Centrifugal Pumps
,”
ASME J. Fluids Eng.
,
102
, pp.
64
–
69
.
4.
Thomae
,
H.
, and
Stucki
,
R.
,
1970
, “
Axial Thrust Occurring in Multistage Radial Pumps
,”
Sulzer Technical Review
.
5.
EPRI Report TR-102102, 1993, “Feedpump Operation and Design Guidelines,” Electric Power Research Institute, Palo Alto, CA, pp. 1/35–1/46.
6.
Senoo
,
Y.
, and
Hayami
,
H.
,
1976
, “
An Analysis on the Flow in a Casing Induced by a Rotating Disk Using a Four-Layer Flow Model
,”
ASME J. Fluids Eng.
,
99
, pp.
192
–
198
.
7.
Stepanoff, A. J., 1966, Centrifugal and Axial Flow Pumps, Wiley, New York.
8.
Makay, E., and Barrett, J. A., 1984, “Changes in Hydraulic Component Geometries Greatly Increased Power Plant Availability and Reduced Maintenance Cost: Case Histories,” Proceedings, The First International Pump Symposium, Texas A&M University, College Station, Texas, pp. 85–97.
9.
Gantar, M., Florjancic, D., and Sirok, B., 2001, “Changes in Hydraulic Component Geometries and its Influence on Axial Thrust in Multistage Pumps” (in German), Industriepumpen+Kompressoren, Vulkan Verlag, Essen, Germany.
10.
Childs, D. W., Elrod, D., and Hale, K., 1988, Annular Honeycomb Seal Test Results for Leakage on Rotordynamic Coefficients; Comparison to Labyrinth and Smooth Configurations, ASME Paper 88-Trib-35, ASME/STLE (1988), Tribology Conference.
Copyright © 2002
 by ASME
You do not currently have access to this content.