Models are presented for the solution of the thermal and mechanical problem of a rigid metallic cylinder indenting an elastic layer with finite thickness which rests on a rigid substrate without friction. The models were extended to turned surfaces applications. With introduction of an equivalent isothermal flux distribution for the mixed boundary problem—constant temperature over the contact area while adiabatic elsewhere along the top surface—an approximate analytical thermal model was developed. The solution was compared to a numerical solution under certain cases. Both solutions in turn compare very well with the generalized three-dimensional expression proposed by prior investigators. The mechanical model predicts the contact half-width under varying mechanical properties, layer dimensions, and applied load. The mechanical contact problem was solved numerically by substituting the displacement variable with a truncated polynomial to get a system of linear equations from which the dimensionless contact half-width was derived. The model is valid throughout a wide range of parameters, including mechanical properties and geometric dimensions. To explicitly predict the dimensionless contact half-width as a function of dimensionless load, a curve was fitted to the numerically obtained solution.
Skip Nav Destination
Article navigation
June 2003
Technical Papers
Thermal and Mechanical Model for Rigid Cylinder Indenting an Elastic Layer Resting on Rigid Base: Application to Turned Surfaces
Zhe Zhang, Graduate Research Assistant,,
Zhe Zhang, Graduate Research Assistant,
Department of Mechanical Engineering, Clemson University, Clemson, SC 29634-0921
Search for other works by this author on:
E. E. Marotta, Senior Engineer/Scientist/Adjunct Professor—Thermal Development,,
E. E. Marotta, Senior Engineer/Scientist/Adjunct Professor—Thermal Development,
IBM Corporation, Server Group, Poughkeepsie, NY 12601-5400
Search for other works by this author on:
J. M. Ochterbeck, Associate Professor,
J. M. Ochterbeck, Associate Professor,
Department of Mechanical Engineering, Clemson University, Clemson, SC 29634-0921
Search for other works by this author on:
Zhe Zhang, Graduate Research Assistant,
Department of Mechanical Engineering, Clemson University, Clemson, SC 29634-0921
E. E. Marotta, Senior Engineer/Scientist/Adjunct Professor—Thermal Development,
IBM Corporation, Server Group, Poughkeepsie, NY 12601-5400
J. M. Ochterbeck, Associate Professor,
Department of Mechanical Engineering, Clemson University, Clemson, SC 29634-0921
Contributed by the Electronic and Photonic Packaging Division for publication in the JOURNAL OF ELECTRONIC PACKAGING. Manuscript received by the EPPD Division July 31, 2001. Guest Editors: Y. Muzychka and R. Culham.
J. Electron. Packag. Jun 2003, 125(2): 186-191 (6 pages)
Published Online: June 10, 2003
Article history
Received:
July 31, 2001
Online:
June 10, 2003
Citation
Zhang, Z., Marotta, E. E., and Ochterbeck, J. M. (June 10, 2003). "Thermal and Mechanical Model for Rigid Cylinder Indenting an Elastic Layer Resting on Rigid Base: Application to Turned Surfaces ." ASME. J. Electron. Packag. June 2003; 125(2): 186–191. https://doi.org/10.1115/1.1568126
Download citation file:
29
Views
Get Email Alerts
Cited By
Sequential Versus Concurrent Effects in Combined Stress Solder Joint Reliability
J. Electron. Packag
Anand Model Constants of Sn-Ag-Cu Solders: What Do They Actually Mean?
J. Electron. Packag
Related Articles
Anisotropic Heat Conduction Effects in Proton-Exchange Membrane Fuel Cells
J. Heat Transfer (September,2007)
Closure to “Discussion of ‘Thermal Contact Resistance of Silicone Rubber to AISI 304 Contacts’ ” [ASME J. Heat Transfer, 122 , p. 403 (2000)]
J. Heat Transfer (May,2000)
Thermal Contact Resistance Modeling of Non-Flat, Roughened Surfaces With Non-Metallic Coatings
J. Heat Transfer (February,2001)
Dependence of Thermal Conductivity and Mechanical Rigidity of Particle-Laden Polymeric Thermal Interface Material on Particle Volume Fraction
J. Electron. Packag (September,2003)
Related Chapters
Further Applications of Spreading Resistance
Thermal Spreading and Contact Resistance: Fundamentals and Applications
How to Use this Book
Thermal Spreading and Contact Resistance: Fundamentals and Applications
Improved Temperature Oscillation Techniques for Measurements of Thermal Diffusivity and Conductivity of Insulation Materials
Insulation Materials: Testing and Applications, 3rd Volume